Vehicles
Sections
109 not categorized PORSCHE 911 TURBO ENDCan't find what you need? Try browsing the Accessories or Exploded Diagrams!Filtered by: 911 1987-89 (includes uncategorized and accessory items) FVD123020ATK Our k24 sport turbocharger is based off the optional k24 turbochargers, found in the GT2 or 993 turbo x50 models. They are remanufactured by borg warner certified technicians in Germany and are a cost-effective solution. The remanufacturing process includes full inspection of the turbocharger to ensure proper operation after the remanufacturing process. We then disassemble, clean and degrease the unit. The compressor wheels are exchanged, lightened and modified for more air flow. All clearances / shaft tolerances are checked for precision to ensure reliability. The end result is 20-30 additional horsepower, in the low and mid rpm range over the factory turbo. The sport turbo also has less lag than a factory k24...(choose a part on the right to read more)
$2,042.70
Make a selection FVD12399600R Silicone boost hose kit FVD's direct replacement boost hose kit eliminates common boost hose "blow outs" on modified turbo's. Facts: tested to withstand over 75 psi (5 bar) boost pressure.fuel and oil resistanttemperature range between - 50 to + 180 degreesbolt on kit over time the OEM boost hoses tend to expand and contract under higher load, which leads to leaks, or "blow outs". Also, the OEM aluminum end does not secure properly into the intercooler, which causes boost leaks, and boost hose blowouts. Our machined billet ends are a perfect secure fit and our silicone hose is designed not to expand under boost pressure. The hose kit is a complete bolt on kit.
$590.70
Make a selection FVD34791130 Enhance steering precision and steering feedback by simply replacing your original tie rods. Turbo tie rods use a spherical inner joint instead of soft rubber bushings. They offer quicker steering response, more sensitivity and more precision. These are standard length we highly recommend them for lowered vehicles with bump steer kits like part # FVD34791100 or FVD347911930 . We also offer turbo tie rods in longer lengths for other applications, check part # FVD34791180r and FVD34791181ry this kit is manufactured in Germany by an OEM supplier, made from high carbon steel and 7075 t6 aluminum. Kit includes: 2 qty. Outer tie rods 2 qty. Inner tie rods 2 qty. Spacing washers 2 qty. Boots 2 qty. Castle nuts 2 qty. ...(choose a part on the right to read more)
$222.24
Make a selection FVD123019ATK Our k24 sport turbocharger is based off the optional k24 turbochargers, found in the GT2 or 993 turbo x50 models. They are remanufactured by borg warner certified technicians in Germany and are a cost-effective solution. The remanufacturing process includes full inspection of the turbocharger to ensure proper operation after the remanufacturing process. We then disassemble, clean and degrease the unit. The compressor wheels are exchanged, lightened and modified for more air flow. All clearances / shaft tolerances are checked for precision to ensure reliability. The end result is 20-30 additional horsepower, in the low and mid rpm range over the factory turbo. The sport turbo also has less lag than a factory k24...(choose a part on the right to read more)
$2,042.70
Make a selection FVD99610053A Kit includes: sport motronic dme exch., sport air filter, sportmuffler TUV, k24-race turbocharger l/r genuine: engine - 6cyl. Boxer twin-turbo capacity - 3600ccm compression ratio - 9,4:1 max. Power - 309kw (415hp) @ 6000rpm max. Torque - 560nm (413lbf ft) @ 3500-4500rpm max. Speed - 305km/h max. Rpm - 6750rpm acceleration 0-100km/h - 4.2s tuning: max. Power - 397kw (540hp) @ 7000rpm max. Torque - 760nm (561lbf ft) @ 4500rpm max. Speed - 331km/h max. Rpm - 7000rpm acceleration 0-100km/h - 3.6s for 27 + years, FVD-Brombacherhas been setting the standard for Porsche engine building and tuning in Germany. Our deep understanding of the flat 6 Porsche engine naturally led to our engine management software. Over the...(choose a part on the right to read more)
$15,139.16
Make a selection FVD95861880MG Genuine: engine - v8 capacity - 4806 ccm compression ratio - 12,5:1 max. Power - 309kw (420hp) @ 6500rpm max. Torque - 500nm @ 3500rpm max. Speed - 256km/h max. Rpm - 7000rpm acceleration 0-100km/h - 6,0s tuning: max. Power - 325kw (442hp) @ 6000rpm max. Torque - 530nm @ 4500rpm max. Speed - 265km/h max. Rpm - 7200rpm acceleration 0-100km/h - 5,7s for 27 + years, FVD-Brombacherhas been setting the standard for Porsche engine building and tuning in Germany. Our deep understanding of the flat 6 Porsche engine naturally led to our engine management software. Over the years we have perfected the art of software tuning, making substantial gains in horsepower and torque, while retaining drivability and most importan...(choose a part on the right to read more)
$1,484.16
Make a selection FVD50599106MM The moshammer front bumper upper air vent is a combination of aggressive styling, aero-efficiency and increased cooling capacity. It is a motorsport finishing touch that complements the entire evo rs (991.2 turbo/s) / stormforce (991.1) / stormforce evo rs (991.2) or downforce rs (991.1 turbo/s) aero packages. FVD Brombacherhas a tradition of offering exclusive body styling that is functional, easily installed, wind tunnel tested, German made and TUV approved. Those high standards naturally led us to the moshammer brand. The moshammer aero styling brand has become a leader in the premium automotive segment. Each part is precision designed and manufactured in Germany for perfect fitment, superior durability and...(choose a part on the right to read more)
$371.80
Make a selection BES98215000SK Brombacher edition valved mufflers are the perfect compromise for you and your loved ones. Rich, deep race car tones with the exhaust valve open and soft subtle, nearly stock sounds with it closed. + 17 hp & + 13 tq gain. - 2 x 3.5 (90 mm) round tips. - includes a pierburg vacuum actuated exhaust valve. - thermal insulation on piping to keep suspension components cool. Withstands up to 2,012 degrees fahrenheit (1,100 degrees celsius). - intoxicating growl at idle, partial throttle and wide open throttle with the valves open. Factory quiet with them closed! - German v2a - x5crni18-10 - 1.4301 stainless steel for improved durability. - "aero quip" style motorsport muffler connections to ensure a leak free exhau...(choose a part on the right to read more)
$5,309.70
Make a selection FVD51299122MM The moshammer vented rear diffuser with fins is an aggressive design that reduces aerodynamic drag. This vented diffuser allows air that is trapped by the rear bumper to exit, allowing for greater top end performance. The design also incorporates 5 fins that improve laminar airflow by reducing turbulence. Moshammer manufactured this as a direct replacement, so it secures seamlessly to the factory locations with the original hardware. This is an ideal addition for a leased vehicle or for those looking to return the car to its original appearance in the future. When added to other elements of the evo rs (991.2 turbo/s) package, the result is a confident, cohesive stance with balanced downforce. Features: vented f...(choose a part on the right to read more)
$1,844.70
Make a selection FVD99661831MG Genuine: engine - 6 cylinder boxer capacity - 3600ccm compression ratio - 11,7:1 max. Power - 265kw (360hp) @ 7200rpm max. Torque - 370nm (273lbf ft) @ 5000rpm max. Speed - 302km/h max. Rpm - 7600rpm acceleration 0-100km/h - 4.8s tuning: max. Power - 276kw (375hp) @ 7000rpm max. Torque - 390nm (288lbf ft) @ 5000rpm max. Speed - 310km/h max. Rpm - 7900rpm acceleration 0-100km/h - 4.6s for 27 + years, FVD-Brombacherhas been setting the standard for Porsche engine building and tuning in Germany. Our deep understanding of the flat 6 Porsche engine naturally led to our engine management software. Over the years we have perfected the art of software tuning, making substantial gains in horsepower and torque, while re...(choose a part on the right to read more)
$1,204.50
Make a selection RES96400100S1 More low and mid-range torque than our race system with cat bypass. Larger primaries, larger collector, largest diameter tubing on the market. Made for mid-range and top end performance with the added beauty of dual exhaust tips! + 25 hp & + 23 torque - 100 cell hjs tri-metallic race catalytics. -2 1/2 tubing (63.5mm) for max. Power across the rpm range.* -weighs 49 lbs. (22 kg). -German v2a - x5crni18-10 - 1.4301 stainless steel for improved durability. - aeroquip cone style catalytic connection design to prevent exhaust leaks. -includes aeroquip quick release clamps. -made in Germany by m&m exhaust, gmbh. -dual round 3 exhaust tips -intoxicating flat 6 growl at idle, partial throttle and wide open throttle. P...(choose a part on the right to read more)
$7,403.00
Make a selection 901989 Forged from the highest quality steel, each torsion bar is centerlessly ground to provide a constant spring rate, chemically coated to protect against rust and then matched in pair sets to ensure that both sides of the car are equally suspended. One needed for entire rear suspension. General Fitment912 1965-69911 1974-77 930 1975-77 911 1978-83 911 1984-86 911 1987-89
$363.18
Make a selection 64455551500 Known as: rubber profile View/Change Diagram
From $2.53
Make a selection 90174180100 Must remove safety pin to operate which is located underneath the warning label - gasket not included View/Change Diagram
From $75.25
Make a selection 91150105400GRV This steel fender joining plate is a prime coated and made by dansk. They offer a complete line of replacement bodywork to complement the entire Porsche model range. All dansk products are manufactured to European standards to ensure the quality that you expect for your Porsche. This commitment has made dansk one of the original equipment suppliers to the Porsche in Germany. Sold individually. 1 necessary per car. Please note: due to variances in production at the factory, age, accident damage or rust, each part may require trimming and or adjustment for perfect fitment. View/Change Diagram
From $105.62
Make a selection 90110534402
From $3.90
Make a selection 199801 These aluminum flywheels are made from the highest quality 6061 t6 aluminum, fantastic for strength, heat dissipation and of course reduction in weight. for the friction surface they use 1045 steel and attach a replaceable friction surface with military grade aerospace fasteners. with these replaceable friction plates there is no need to replace the entire flywheel when the clutch or flywheel is at the end of it’s life, saving time and money. the ring gears are made from 1050 steel and are heat treated for durability. the flywheel ring gears are heated then pressed on and secured with grade 8 button screws. fidanza flywheels are engineered to perform. General Fitment911 1984-86911 1987-89
$734.74
Make a selection 20903CK In order to provide superior performance and lasting durability, this premium new clutch kit utilize "tier-1" content that is manufactured to exacting o.e.m. Standards. All components are engineered to function as a precisely matched system. Includes all-new pressure plate assemblies, disc assemblies, release bearings, pilot bearings/bushings (if applicable). Pressure plate assemblies are functionally tested for lift-off, balance, clamp load, release load, and finger height. Disc assemblies are functionally tested for lateral run-out, compressed thickness, torsion durability, and spring rate. Release bearings meet exact OEM fit, form, and function specifications to ensure the ultimate in load carrying capabil...(choose a part on the right to read more) General Fitment911 1987-89
$1,399.95
Make a selection 93055932200 Protect your paint. Flying road debris will nick your paint and lead to rust and other exterior problems. These black vinyl 3M stone guards will protect your fenders. These are sold for the rear fenders individually. View/Change Diagram
From $37.70
Make a selection HR5505 If you have room in your fender well to spacer your wheels out, here is an easy way to improve your Porsche’s handling. Made of aluminum/magnesium alloy these hard anodized spacers are hub-centric and up to 70% lighter than typical steel wheel spacers. Made in Germany. Spacers come with wheel bolts, studs and nuts. This is a special item and cannot be returned if packaging has been opened. General Fitment924 1986-88944 1989-91 944 1985-88 944 1982-85 928 1992-95 928 1987-91 928 1983-86 928 1978-82 968 1992-95 911 1974-77 930 1975-77 911 1978-83 911 1984-86 911 1987-89 911 1989-94 911 1994-98 911 1998-05 356 1960-65 912 1965-69 BOXSTER 1997-04 BOXSTER 2005-08 911 1970-73 911 1965-69 CAYMAN 2006-08 CAYENNE 2003-06 CAYENNE 2007-10 911 2005-08
$139.95
Make a selection P201C Reinforcement front suspension mount. Note: it is highly recommended to be welded in after suspension has been bolted to car for correct placement. These reinforcements give extra strength to the studs, reducing flex and reducing the possibility of the studs ripping out. General Fitment911 1974-77930 1975-77 911 1978-83 911 1984-86 911 1987-89
$18.00
Make a selection 910165 Forged from the highest quality steel, each torsion bar is centerlessly ground to provide a constant spring rate, chemically coated to protect against rust and then matched in pair sets to ensure that both sides of the car are equally suspended. All torsion bars are guaranteed for 3 years against breakage. Note: worn torsion bar bushings will shorten the life of torsion bars. Our 3-year guarantee will remain valid only when bushings are in good condition at time of installing new torsion bars. Sold in pairs. General Fitment911 1974-77911 1978-83 911 1984-86 911 1987-89 930 1975-77 911 1970-73 911 1965-69 912 1965-69 914 1970-76
$458.05
Make a selection 91164170129 Its always nice to know how fast you are going, especially when asked by a friendly officer of the law. However, older gauges have a tendency to fail or be out of calibration. Instead of buying a replacement gauge, which can cost hundreds of dollars, we offer a rebuild service that will restore your malfuncioning gauge to as-new condition. Simply send us your malfunctioning gauge with a detailed description of the issue and we will have it rebuilt and sent it back to you in short order. Stop dealing with a broken or uncalibrated gauge in your Porsche! We also offer the ability to change your gauge faces to any number of custom colors (please call for details before ordering). View/Change Diagram
From $350.00
Make a selection 91135195006D Pbr deluxe pads are an excellent upgrade without many trade-offs. They provide better than stock braking while being rotor-friendly and generating less dust. General Fitment911 1974-77911 1978-83 911 1984-86 911 1987-89
$31.09
Make a selection 909278 Forged from the highest quality steel, each torsion bar is centerlessly ground to provide a constant spring rate, chemically coated to protect against rust and then matched in pair sets to ensure that both sides of the car are equally suspended. One needed for entire rear suspension. General Fitment911 1974-77930 1975-77 911 1978-83 911 1984-86 911 1987-89 912 1965-69
$363.18
Make a selection © 2024 Automobile Atlanta Inc. 505 S. Marietta Pkwy • Marietta, GA 30060 • Order By Phone: 800 792 4944 770 427 2844 |